Yenko Camaro

The Yenko Super Camaro was a modified Chevrolet Camaro prepared by Yenko Chevrolet, under the command of Don Yenko. The originals were all first-generation Camaros. When the Camaro debuted, a General Motors corporate edict prevented it from carrying an engine larger than 400 in³ (6.6 L) V8; this put the Camaro at a serious disadvantage to the Ford Mustang and Plymouth Barracuda, since neither Ford nor Plymouth had a such a limit. Don Yenko, however, knew there was a market for an ultra powerful Camaro and found ways around the GM limit.

Yenko Camaro
1969 Yenko Camaro from the Petersen Automotive Museum
ManufacturerChevrolet
Parent companyGeneral Motors
Production1967-1969
AssemblyVan Nuys, California
Norwood, Ohio
Classpony car
muscle car
sports car
Body style(s)2-door coupé
2-door convertible
LayoutFR layout
PlatformF-body
Engine(s)6.6L V8
7.0L V8
Transmission(s)4-speed manual

2-speed automatic

3-speed automatic
ManualsService Manual

1967

Yenko ordered L-78 equipped SS Camaros and swapped in the Chevrolet Corvette's L-72 427 in³ (7.0 L) V8. The cars came with a 4.10 rear end and heavy-duty suspension. The exact number of cars produced is not known; most estimates are around 50. Yenko also installed a fiberglass replacement hood similar to the "Stinger" hood featured on 1967 big-block Corvettes.

Don Yenko's Camaros were equipped with a 427ci L-72 in them with either an M21 or M22 transmission. The horsepower was rated at 423 hp (315 kW). Yenko Camaros were not allowed to race for Chevrolet on the drag strip because they were not made by Chevrolet. Chevy's answer to this was the Copo Camaro, or Central Office Production Order, in 1969. The Copo Camaros were equipped with the same 427ci engine and were allowed to race for Chevy.

1968

Encouraged by the success of the 1967 model, Yenko continued to produce his Camaros. All cars came equipped with the M-21 close-ratio four speed manual transmission. A large, twin-scooped hood replaced the "Stinger" version, and Yenko badges graced the sides and tail light plate. The COPO model came with upgraded suspension, 140 mph speedo and other items but not the 427 ci engine. Yenko swapped the 396 ci engine for these up until 1969 when they were installed by Chevrolet. There is speculation that one 1968 Camaro came from the factory in 1968 with a 427 ci engine making it one of the most valuable collector cars to exist.

As of Sat. Jan. 17th 2009 at the Barret Jackson Auto Auction, a rebodied, silver 4spd Yenko went for $121,000.

1969

For 1969, the dealership worked with Chevrolet to have the L-72 engines installed on the factory assembly line using a Central Office Production Order, or COPO. The orders included power disc brakes, a 4.10 Positraction rear end, a stronger front stabilizer, and a heavy-duty 4-core aluminum radiator. Buyers of the car had the option of either the M-21 four speed or the Turbo Hydramatic 400 automatic transmission. A total of 201 cars were sold in 1969, 171 with four speed transmissions and 30 with automatic transmissions. Yenko rounded out the visual package with front and rear spoilers, a cowl-induction hood, special "Yenko 427" badges, twin stripes down the flanks and hood, and the sYc (Yenko Super Car) badge.

Almost 40 years later, these Camaros have been appraised and sold for well over $2.2 million USD at Barrett-Jackson auctions. As of sep 2008, there are 2 known automatic transmission 1969 Yenko Camaro's. as stated by ESPN auction show.

As of Jan 17th 2009, a REAL ZL-1 Copo, dark green, re-bodied, went for $290,000 at the Barret Jackson Auto Auction Lot 12773. Mr. October Reggie Jackson was bidding on this car but didn't win it. Another yellow, original body, non original heads with Auto transmission for $270,000. Both are said to be a steal and the deals of the show.

1981

See Second-generation Chevrolet Camaro

1981 was Don Yenko's last run at making the ultimate performance car.

The 1981 Yenko Turbo Z, as it was known as, was based on a 1981 Camaro.

Don Yenko's comments on the car are:

From a performance standpoint, cars have shown a slow but steady decline in the last ten years. Low compression engines to accommodate low octane fuel, are now the norm. Ever-increasing numbers of emissions controls have sapped their share of horsepower from once potent engines. To recover these accumulated horsepower losses without increasing pollution presents a real challenge. After months of testing and development we have done it. Working closely with some competent people at Turbo International a system emerged that does everything we hoped for. This system, like all others, captures the energy to improve the induction of fuel/air mixture. The similarity to the other systems stops right here. Our system uses no priority valve so there's no turbo-lag. We don't have a waste gate to malfunction either. And since all of the fuel entering the engine is "processed" through the turbo, you get better fuel economy and improved response even without being in boost. Every nut, bolt and fitting used in this system is the best available. This has all been developed with each and every emission control connected and functional.[1]

1969 Continuation Series

Recently a company out of North Carolina called Classic Automotive Restoration Specialists[2] has restarted production of the '69 Yenko Camaro. Don Yenko sold 201 of his infamous COPO-program Camaros out of his Canonsburg,PA dealership. As reported in the March '08 issue of Muscle Car Review the vehicle is a fully licensed and certified Yenko starting at #202. The 427 engine under the hood was built by GM who has brought back the big block engines from the muscle car era. The rest of the components took 2 1/2 years to track down the original machinery. Options offered on the vehicle are the same as was available back in 1969 including paint colors. The car costs around 60% less than some of the current 39-year old Yenko Camaro survivors but drives like an old car would have when it was new off the Canonsburg, PA dealership.

External links